View FTR-1629-17_4450718.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Preliminary Product Specification DWDM GBIC Transceiver FTR-1629-XX
PRODUCT FEATURES * * * * * * * * * Up to 1.25 Gb/s bi-directional data links Standard GBIC footprint Temperature-stabilized DWDMrated DFB laser transmitter 100GHz ITU Grid, C Band Very low jitter Metal enclosure for low EMI Extended operating range: 0C to 70C case temperature Wavelength controlled within 0.1 nm over entire temperature range Extended link budget of 30dB with APD receiver technology APPLICATIONS * * * ITU grid optical networks Bandwidth aggregation Ring topologies with OADM
Finisar's Dense Wavelength-Division Multiplexing (DWDM) transceivers offer DWDM transport with dramatically lower power and cost in a standard plugable GBIC package. The FTR-1629 is designed expressly for service providers deploying DWDM networking equipment in metropolitan access and core networks. The fiber link budget has been enhanced to 30dB with an Avalanche Photo Diode (APD) receiver.
The FTR-1629 has serial identification features as described for Module Definition "4"
GBICs in the GBIC Specification Revision 5.51 . In addition, digital diagnostic features are implemented as described in Finisar Application Note AN-2030, "Using the Finisar GBIC I2 C Test/Diagnostics Port"2 .
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 1
Finisar
PRODUCT SELECTION
Product Code FTR-1629-17 FTR-1629-18 FTR-1629-19 FTR-1629-20 FTR-1629-21 FTR-1629-22 FTR-1629-23 FTR-1629-24 FTR-1629-25 FTR-1629-26 FTR-1629-27 FTR-1629-28 FTR-1629-29 FTR-1629-30 FTR-1629-31 FTR-1629-32 FTR-1629-33 FTR-1629-34 FTR-1629-35 FTR-1629-36 FTR-1629-37 FTR-1629-38 FTR-1629-39 FTR-1629-40 FTR-1629-41 FTR-1629-42 FTR-1629-43 FTR-1629-44 FTR-1629-45 FTR-1629-46 FTR-1629-47 FTR-1629-48 FTR-1629-49 FTR-1629-50 FTR-1629-51 FTR-1629-52 FTR-1629-53 FTR-1629-54 FTR-1629-55 FTR-1629-56 FTR-1629-57 FTR-1629-58 FTR-1629-59 FTR-1629-60 FTR-1629-61 Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1 Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 2
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
I.
Pin Out Pin Name
RX_LOS GND GND MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) TX_DISABLE GND GND TX_FAULT GND -RX_DAT +RX_DAT GND VCC VCC GND +TX_DAT -TX_DAT GND
Pin #
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Sequence
2 2 2 2 2 2 2 2 2 2 1 1 1 1 2 2 1 1 1 1
Table 1. GBIC to Host Connector Pin Assignment
"Sequence" indicates the order in which pins make contact when the device is hot plugged. See "Table 3: Signal Definitions" in the GBIC Specification Revision 5.51 for a description of the function of each pin listed above.
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 3
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
II.
Electrical Power Interface
The GBIC specification calls for a range of 4.75V to 5.25 volts as described in Table 2. The maximum voltage of 6V is not to be applied continuously.
Parameter Supply Current Inrush Current Maximum Voltage Input Voltage Symbol Is Isurge Vmax Vcc 4.75 5.0 Min Typ 250 Max 400 350 30 6 5.25 Units mA mA mA V V Referenced to GND Notes/Conditions Tc <= 70o C Tc <= 65o C
<= 300 msec above steady state current
Table 2. Electrical Power Interface
III.
Low Speed Signals
RX_LOS, TX_DISABLE, and TX_FAULT are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA) are open drain CMOS signals (see section XI, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. For more detailed information, see sections 5.3.1 - 5.3.8 in the GBIC Specification Revision 5.51 .
Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW Symbol VOL Min 0 Max 0.5 Units Notes/Conditions V
GBIC Input HIGH
4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc host_Vcc + V 4.7k to 10k pull-up to host_Vcc, 0.5 0.3 measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low Speed Signals - Electronic Characteristics
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 4
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay RX_LOS Negate Delay TX_DISABLE Assert Time
Symbol
Min -42
Typ -39 -37 1
Max
Units Notes/Conditions dBm dBm dB sec sec sec sec
-32 300 150 100
t_loss_on t_loss_off t_off
From detection of loss of signal to assertion of RX_LOS From detection of presence of signal to negation of RX_LOS Rising edge of TX_DISABLE to fall of output signal below 10% of nominal Falling edge of TX_DISABLE to rise of output signal above 90% of nominal. Time indicated is under steady-state temperature conditions. TX_DISABLE HIGH before TX_DISABLE set LOW TX_Fault will assert before the device is outside of specified wavelength range
TX_DISABLE Negate Time
t_on
1000
TX_DISABLE Reset Time TX_FAULT Assert
t_reset
10 -0.1 0.1
sec nm
Table 4. Low Speed Signal Parameters
IV. High Speed Electrical Interface All high-speed PECL signals are AC coupled internally.
Parameter Data Input Voltage Data Output Voltage PECL rise/fall Bit Error Rate Tx Input Impedance Rx Output Impedance Symbol Vin Vout Tr,Tf BER Zin Zout Min 650 370 Typ Max 2000 2000 150 10-12 75 75 Units mV mV psec Ohm Ohm Notes/Conditions PECL differential peak - peak PECL differential peak - peak 20% -80% Differential PRBS 27 - 1 test data pattern
Table 5. High Speed Electrical Interface
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 5
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
V.
Parameter
Optical Parameters
Symbol Min Typ Max Units Notes/Conditions
TRANSMITTER CHARACTERISTICS Center Wavelength Spacing Spectral Width Transmitter Center Wavelength - End of Life Transmitter Center Wavelength - Start of Life Side Mode Suppression Ratio (SMSR) Optical Rise/Fall Time Transmitter Optical Output Power Transmitter Extinction Ratio Transmitter Eye Opening 20 c c SMSR tr / tf Pout OMI X - 100 X -80 30
100 0.2 X X-50 0.3 X + 100 X-20
GHz nm pm pm dB 200 +3 ps dBm dB %
Corresponds to approximately 0.8 nm Full width, -20dB from max X = specified center wavelength X = specified center wavelength Modulated Unfiltered, 80% -20% Average power coupled into single mode fiber IEEE 802.3 and Fibre Channel Eye Mask Margin Peak to peak, filtered Peak to peak, -25 d Bm RX power
0 9 40
Total Transmitter Jitter RECEIVER CHARACTERISTICS Receiver Jitter Generation
100 100
ps ps
Optical Input Wavelength - Pin 1450 1620 nm DWDM C-Band Optical Input Power Pin - 30 -7 dBm 1.25Gb/s w/ (BER < 10 -9 ) PRBS 2 7 -1 Optical Input Power Pin - 28 -7 dBm 1.25Gb/s w/ (BER < 10 -12 ) PRBS 2 7 -1 Optical Input Power - 6 dBm Receiver Damage Threshold Receiver Reflectance RRX -14 dB Power Penalty 3.0 dB See note 3 Note 1: Parameters are specified over temperature and voltage, at end of life unless otherwise noted. Note 2: All parameters are measured on a Finisar GBIC Evaluation Card unless otherwise noted. Note 3: Measured in loop back at BER= 10-12 with 3600 ps/nm dispersion, 20dB ONSR, 1.25Gb/s data rate, and PRBS 2 7 -1 pattern.
Table 6. Optical Parameters
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 6
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
VI. Wavelength Stabiliza tion The laser transmitter will not be turned on until its temperature is adjusted to ensure operation within the specified channel (X +/- 0.4nm). This temperature stabilization time is dependent on the ambient temperature conditions, but will typically occur within 30 seconds of powering the GBIC. The device will transmit within the specified wavelength tolerance (X +/- 0.1nm) within 5 seconds of transmitter operation.
VII. General Specifications
Parameter Data Rate Symbol BR Mi n 1.06 Typ Max 1.25 Units Notes/Conditions
Gb/sec Fibre Channel, IEEE 802.3 compatible Total System Budget 28 30 dB @ 1.25 Gb/s, BER <10-12 w/ PRBS 2-7 -1. See Note 1 Note 1: Total system budget is defined as Pout - Pin - typical connector losses. Table 7. General Specifications
VIII. Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to +60C. Finisar FTR-1629-XX GBICs have an extended range from 0C to +70C case temperature as specified in Table 8.
Parameter Operating Temp Symbol Top Min 0 Typ Max 70 Units Notes/Conditions C
Case temperature measured on top-side of device Storage Temp Tsto -10 85 C Ambient temperature Eye Safety CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Table 8. Environmental Specifications
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 7
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
IX. Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for `Module Definition "4"' as outlined in Annex D of the GBIC Specification 1 . These GBICs use an Atmel AT24C01A 128 byte E2 PROM at address A0H. For details on interfacing with the E2 PROM, see the Atmel data sheet titled "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2 PROM."3 Finisar's DWDM GBICs also support extended diagnostic features as described in Finisar Application Note AN-2030, "Using the Finisar GBIC I2 C Test/Diagnostics Port"2 . A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H.
Parameter I2 C Clock for Atmel (A0H) and Controller IC (A2H)
Symbol Catmel
Min 0
Typ
Max 100,000
Units Notes/Conditions Hz Bus can be driven blind
Table 9. I2 C Timing Requirements
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 8
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
X.
Mechanical Specifications
Finisar's DWDM GBICs conform to the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61 .
Parameter GBIC insertion GBIC extraction GBIC retention Symbol FI FE FR Min 0 0 130 Typ Max 20 15 Units Newtons Newtons Newtons Notes/Conditions ~4.5 lbs ~3.3 lbs Straight out ~29.3 lbs
Table 10. Insertion, Extraction, and Retention Forces
Figure 1. DWDM GBIC Outline Drawing
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 9
FTR-1629-XX DWDM GBIC Preliminary Product Specification - June 2003
Finisar
XI. Ordering Information Part Number FTR-1629-XX Description DWDM GBIC with APD Receiver XX = channel number (see product selection on page 2)
XI. References 1. "Gigabit Interface Converter (GBIC) Revision 5.5".(*) Sun Microsystems Computer Company et. al., August 16, 1999. http://playground.sun.com/pub/OEmod/
2. "Application Note AN-2030: Digital Diagnostic Monitoring Interface for SFP Optical Transceivers", Finisar Corporation, April 2002. 3. "AT24C01A/02/04/08/16 2-Wire Serial CMOS E2 PROM". Atmel Corporation. www.Atmel.com
For More Information: Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 sales@finisar.com www.finisar.com
(c) Finisar Corporation Rev D, June 2003
PRELIMINARY and Confidential
Page 10

▲Up To Search▲

Price & Availability of FTR-1629-17

	To Download FTR-1629-17 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .